February 16, 2022
-
Supports
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design -
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design
DT-I/O USB to UART Converter
DT-I/O product
DT-I/O USB to UART Converter is a USB to RS-232 or USB to RS-485 converter module which support full duplex and data rate up to 500kbps. This module uses power source from USB line or 5VDC external power supply. Available LED indicator for power source, data transmitter, data receiver, etc. This module support eight signal from RS-232, such as (DCD, RX, TX, DTR, RTS, CTS and RI).
Dimension : 7 cm (L) x 6 cm (W) x 1,8 cm (H)
- Product Detail
- Download
- Application Note
Specifications :
- Two option for two ways convertion :
- USB to RS-232.
- USB to RS-485.
- 500 kbps for data rate.
- Uses USB type B connector.
- DB-9 connector for RS-232.
- Support DCD, Rx, Tx, DTR, DSR, CTS, CTS and RI signal.
- Can be used as DTE on USB to RS-232 mode.
- Comes with RJ-45 for RS-485 port.
- Comes with jumper configurartion for termination resistor on RS-485.
- Data receptionon RS-485 and auto power down can not be used while USB on suspend state.
- When auto power down for RS-232 is active, then RS-232 driver will active if any valid data on DB-9 connector.
- Comes LED indicator for input voltage, data transmit, data receive RS-232 vaildity signal.
- 5VDC input voltage (from USB or DC jack).
- Selection of power souce by jumper configuration.
- Comes with USB driver.
- Available datasheet, manual, procedure testing, schematic circuit and example code.
Includes :
- 1x DT-I/O USB TO UART CONVERTER.
- 1 USB Cable.
Application Note Table
| Article | File | Desc | date |
|---|---|---|---|
| |
AN171.zip | [AN171] Smart Monitoring and Control System dengan menggunakan jalur komunikasi RS-485This application note will explain how to build a simple smart monitoring system. This application note uses DT-I/O USB to UART Converter, DT-I/O NEO RS-232 to RS-485 Converter, DT-I/O Neo Relay Board, DT-Sense Barometric Pressure & Temperature Sensor, DT-AVR Low Cost Micro System, and DT-AVR Low Cost Nano System. |
28-04-2014 |
| |
AN164.zip | [AN164] Komunikasi Jarak Jauh antara 2 PC dengan RS-485This application note will explain how to build a RS-485 communication between 2 PCs. This application note uses DT-I/O USB to UART Converter and DT-I/O NEO RS232 to RS485 Converter. |
28-04-2014 |
Raspberry Pi Home Remote App Kit
June 05, 2018
April 12, 2017
April 12, 2017
June 02, 2016
June 02, 2016
June 02, 2016
April 27, 2016
