February 16, 2022
-
Supports
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design -
Technical Support Email
support@innovativeelectronics.com
If you have trouble on the usage of our products (except for DT-51 Trainer Kit)tutorial51@innovativeelectronics.com
If you have trouble on the usage of our DT-51 Trainer Kit productsiewebmaster@innovativeelectronics.com
If you have any feedback relating to the IE Website Design
DT-51 I²C ADDA
DT-51 product
*) DISCONTINUE. Upgrade to DT-I/O I²C ADDA Ver2.0
DT-51 I2C ADDA is an Analog Input Ouput Add-On Board for 89C51 Development Tools DT-51 that using I2C-Bus interface. DT-51 I2C ADDA is uses to convert analog signal such as voltage or current into binary data and vice versa. Example application for DT-51 I2C ADDA is speed motor control, room temperature control, remote data acquisition, and others.
DT-51 I2C ADDA is designed as add-on board for DT-51 Ver 3.0, but it is possible to be connected with another microprocessor or microcontroller system. Recommended to read up schematic and application diagram of PCF8591 if you want to connecting DT-51 I2C ADDA with another system. All of documentation can be found on Floppy disk.
Dimension : 6,1 cm (P) x 5,3 cm (L) x 1,4 cm (T)
- Product Detail
- Download
- Application Note
Specifications :
- Fully compatible with 89C51 Development Tools DT-51.
- Only needed 2 wires for connect to the another microprocessor or microcontroller.
- Four 8-bit Analog Input (Analog to Digital Converter /ADC) channels which can be programmed as a single-ended or differential inputs.
- One 8-bit Analog Output (Digital to Analog Converter / DAC) channel.
- Each DT-51 I2C ADDA is equipped with jumper connector to assign I2C address, so can be expanded to 8 boards without additional hardware.
- Comes with 'track & hold' circuitry.
- Provide ready-to-use design procedure to ADC or DAC.
Application Note Table
| Article | File | Desc | date |
|---|---|---|---|
| |
AN9.zip | [AN9] 8 Channel Temperature DisplayThis application note will explain how to display temperature data on DT-51 KND. The analog voltage output from two temperature sensor ICs to be changed on digital data by DT-51 I2C ADDA and the next step is to display temperature data on DT-51 KND. (Application Note in Indoensian Language) |
25-04-2014 |
| |
AN8.zip | [AN8] Temperature Display with Graphic LCDThis application note will explain how to display temperature on Graphic LCD. The analog output voltage from analog temperature sensor IC to be changed in digital data by DT-51 I2C ADDA and futher processed for display to the 128x64 Graphic LCD. (Application Note in Indonesian Language) |
25-04-2014 |
| |
AN89.ZIP | [AN89] Konversi Tegangan Analog - Digital IIThis application note will explain how to use DT-51 I2C ADDA v2.0. This application note uses DT-AVR Low Cost Micro System / Low Cost Nano System and DT-51 I2C ADDA v2.0. |
25-04-2014 |
| |
AN77.zip | [AN77] Low Cost ADDA IIThis application note will explain how to build a servo controller. This application note uses DT-51 Low Cost Nano System / Low Cost Micro System and DT-51 I2C ADDA. |
25-04-2014 |
| |
AN65.zip | [AN65] Konversi Tegangan Analog - DigitalThis application note will explain how to build a ADC application. This application note uses DT-BASIC Nano System / Micro System / Mini System and DT-51 I2C ADDA. |
25-04-2014 |
| |
AN56.zip | [AN56] Low Cost ADDAThis application note will explain how to build Analog to Digital or Digital to Analog application. This application note uses DT-51 Low Cost Micro System and DT-51 I2C ADDA. |
25-04-2014 |
| |
AN43.zip | [AN43] Air Quality Sensor IIThis application note will explain how to build an air quality monitoring system. This application note uses DT-51 Minimum System ver 3.0 and TGS2600 gas sensor. |
25-04-2014 |
| |
AN42.zip | [AN42] Kontrol Suhu IThis application note will explain how to build a temperature controller. This application note uses DT-51 PetraFuz and DT-51 I2C ADDA and de KITS Relay Board. |
25-04-2014 |
| |
AN27.zip | [AN27] Weather Station IThis application note will explain how measure temperature and humidity using LM35 as the temperature sensor, RHK1AN as the humidity sensor, DT-51 I2C ADDA as the ADC module and DT-51 Minimum System ver 3.0 as the main controller. (Application Note in Indonesian Language) |
25-04-2014 |
Raspberry Pi Home Remote App Kit
June 05, 2018
April 12, 2017
April 12, 2017
June 02, 2016
June 02, 2016
June 02, 2016
April 27, 2016
